Data Nominal Ordinal Interval Ratio Hot Sex Picture Hi, i would like to know how we can convert a fluid filter absolute micron rating to nominal micron rating. if there is a way. thanks. dtai. Dear all, i'm an ealry graduated mechanical engineer and in my company i'm working on design of static equipments as p.vessel,tank and heat exhangers. concerning to pressure vessel, i would like to know, if i have a working capacity of 13m^3, which one could be a nominal capacity that could.
Nominal Ordinal Interval And Ratio Data Sumit, reply to ur queries : if you tell me what is the use of uw 40 (f) (1) through (6) ? reply this clauses explain definition of nominal thickness for various weld configurations like butt weld fillet weld groove weld etc. and ucs 56 (d) (1) through (5) term ? reply limits for cooling heating rate, furnace atmosphere etc. is defined. based on which one has to decide the cycle of heat. The present nema standard is to nameplate motors at 460v for operation on a nominal 480v system. this allows for the unavoidable voltage drop that occurs between the main bus and the motor. Thanks to your reply, but i have ill conditioned my question, sorry! starting from the list of elements that constitute an alloy (generally expressed in a range format, as stated in asme ii a or ii b), there is a "criteria" by which it is possible to group a specific alloy under one of the possibly "family" listed in asme ii part d or create a new "family" of alloy? example: p355nh of en 10028. The aeronautical sense of nominal derives from engineering where the nominal value is the specified dimension and the reference point for tolerances. the free dictionary offers the following definition (from mcgraw hill dictionary of scientific & technical terms, 6th edition) for tolerance: (engineering) a permissible deviation from a specified value, expressed in actual values or more often.
Nominal Ordinal Interval Ratio Explained Simply Grad Coach Thanks to your reply, but i have ill conditioned my question, sorry! starting from the list of elements that constitute an alloy (generally expressed in a range format, as stated in asme ii a or ii b), there is a "criteria" by which it is possible to group a specific alloy under one of the possibly "family" listed in asme ii part d or create a new "family" of alloy? example: p355nh of en 10028. The aeronautical sense of nominal derives from engineering where the nominal value is the specified dimension and the reference point for tolerances. the free dictionary offers the following definition (from mcgraw hill dictionary of scientific & technical terms, 6th edition) for tolerance: (engineering) a permissible deviation from a specified value, expressed in actual values or more often. It turns out that paragraph uw 16 (minimum requirements for attachment welds at openings) (f) (3) ( 6) states the following: " in lieu of the thickness requirements in ug 45, the minimum wall thickness for fittings shall not be less than that shown in table uw 16.1 for the nearest equivalent nominal pipe size. ". "nominal" is another question. perhaps there is some tolerance for larger than normal aggregate that's not predominant in the size distribution. question i) do 25.2.1 and 25.2.2 apply independently? the second one is spacing between layers of rebar, i'd expect that the bar spacing needs to work for the max aggregate size on both layers. What is the difference between nominal and finished thickness? thank you. s1111 sort by date sort by votes aug 7, 2007 #2. Hello everyone, i'm trying to obtain the strains from a model. i request the "e" variable into the .inp in order to do so but what i found into the odb is the "le" (logarithmic strain). does anyone knows why? is there anyway to change between them mathematically?.
Levels Of Measurement Nominal Ordinal Interval Ratio 48 Off It turns out that paragraph uw 16 (minimum requirements for attachment welds at openings) (f) (3) ( 6) states the following: " in lieu of the thickness requirements in ug 45, the minimum wall thickness for fittings shall not be less than that shown in table uw 16.1 for the nearest equivalent nominal pipe size. ". "nominal" is another question. perhaps there is some tolerance for larger than normal aggregate that's not predominant in the size distribution. question i) do 25.2.1 and 25.2.2 apply independently? the second one is spacing between layers of rebar, i'd expect that the bar spacing needs to work for the max aggregate size on both layers. What is the difference between nominal and finished thickness? thank you. s1111 sort by date sort by votes aug 7, 2007 #2. Hello everyone, i'm trying to obtain the strains from a model. i request the "e" variable into the .inp in order to do so but what i found into the odb is the "le" (logarithmic strain). does anyone knows why? is there anyway to change between them mathematically?.
Comments are closed.